Digital Control Lamps Light Testing Equipment Adjustment Devices Of Torsion And Bending Test According To IEC60598

Digital Control Lamps And Lanterns Adjustment Devices Of Torsion And Bending Test According To IEC60598 Clause 4.14.3

Product information

The device is used to detect adjustment device, and confirm to the IEC60598-1 clause 4.14.3.

The adjustment device, equipped with the appropriate cable or cord shall be operated in accordance with following table . A cycle of operation is a movement from one extreme of the range to the other and back to the starting position. The rate of movement shall not cause the device to heat appreciably and shall not exceed 600 cycles per hour.
For adjusting devices that consist of a flexible tube, the range of adjustment for this test is normally 135° in both directions from the vertical. However, where this adjustment cannot be achieved without using unreasonable force, the flexible tube is bent only to the positions where it will remain by itself.

Technical Parameters

Operation Procedures

Preparation work:

Access to 220V/50HZ power supply, turn the [POWER] switch on, and the [STOP] indicator light on, indicate the power accessed. Check the [E-STOP] button bounced or not. Install the sample load, install the power cord, and plug the power cord into the load socket according to the station.

Parameters Setting:

The following parameters should be set according to the relevant standards before starting the test.

【Test Times】: Set the Test Times.

【Manually Speed】: Enter swivel angle per second, suggested 10°-20°/s, the starting position cannot be well controlled if the manually speed is too fast.

【Swivel Times/Min】: Set swivel speed as per test requirement. The value bigger, the swivel speed faster, and vice versa.

【Swivel Angle】: Set swivel angle (full angle value) as per test requirement.

0 ° Position Confirmation

In the [0°Position Confirmation Interface], press [Manually Rotate Clockwise] or [Manually Rotate Counterclockwise]make the pointer of the manipulator swivel to position of 0° in dial(or any position), then press [Starting Position Confirmation] . Clear the value of [Current Position], and the starting position (0°) is confirmed.

Press [Manually Rotate Clockwise] or [Manually Rotate Counterclockwise] again, make the manage left starting position , check whether the display value in [Current Position] matches the value on the dial, after that, press [Homing], the manipulator will back to starting position, the display value in [Current Position] shown as 0. Starting position confirmed.

The 0° position can be set arbitrarily in any position of dial 360°base on requirement. Setting method same as above.

Guangzhou HongCe Equipment Co., Ltd (hereinafter referred to as HongCe) is located in Guangzhou, China, since 2003, engaged in developing and providing test equipment and detection system for electronic & electrical products, house appliances and other products. HongCe is professionally dedicated in providing laboratory testing equipment and production line testing system, we are now the high-tech enterprises with technical superiority and R & D capabilities in test instruments industry.

Our core technologies encompass vacuum, leak testing & automatic control, laboratory test equipment & solution. Our technical leader is an expert in leak detection, his more than 2 decades of experience are a great asset to our firm. Our technical team is comprised of wellexperienced engineers and technicians.

HongCe laboratory testing equipment are designed and manufactured as per the requirements of GB, IEC, EN, UL, VDE, BS, AS, ISO standards and etc. Our main products are: switch, plug, socket and coupler test equipment; mechanical strength impact test equipment; material fire hazard test equipment, enclosure protection test probes; waterproof and dustproof environmental testing equipment; household appliances testing equipment; wire and cable testing equipment; luminaires test equipment; electric tools test equipment; information technology and audio & video test equipment. Our products are widely used in domestic and worldwide measurement & certification institutions, inspecting mechanism, laboratories, export & import inspection and quarantine bureau, various production companies and etc. Our customer includes Bureau Veritas, CSA, ITS, UL, TUV Rheinland, TUV SUD, SGS and etc.

HongCe production line testing equipment are mainly customized according to client's workpieces, such as automatic leak testing system, gas recovery system, other tailor-made system based on vacuum & leak testing technology.