Combined Environmental Test System For Satellite Parts Vibration And Temperature Test

1. External Environmental Conditions

Ambient temperature: 0°C~35°C , RH: 85%,Ambient pressure: normal atmosphere

Power supply: 380V±10%,50Hz+N+G,RG: ≤4 Ohm

2. Main characteristics of temperature and humidity

► Temperature Range:-40℃～+150℃

► Temperature Constancy:≤ ±0.5°C

► Temperature Uniformity: ≤ 2℃；

► Temperature Deviation:≤ ±2°C

► Temperature rate of chang(Measured at 20±2°C of ambient temperature, averaged throughout)

Heating rate:+20℃→+150℃ ≥3℃/min；(No load, average throughout)

Cooling rate:+20℃→ -40℃ ≥2℃/min；(No load, average throughout)

► Humidity range:10%~98%( See below temperature and humidity range chart, no heat dissipation load)

► Humidity deviation: +2/-3±%RH( ＞ 75%RH) ±5.0%RH(Humidity ≤75%RH)

► Humidity uniformity:≤+2/-3%RH(＞75%RH时)≤±5%RH(≤75RH)

3. Main features of size

► Internal effective volume:about 2000L

► Inner size:1400 x 1400 x 1000mm (W x D x H)

► External dimensions of the chamber:about 3900 x 2400 x 2800 mm (W x D xH) (Subject to the final design)

► With the vibration table size:slip table≤1000 x 1000mm；Head Expander≤1000 x 1000mm

4. Refrigerating system

► The mechanical cooling is provided by a cascade system, which is realized by two advanced piston compressors. The main body is made of special cast iron, easy-to-integrate cylinder and light metal alloy piston.

The cooling system has an automatic compressor protection system, and an injection system can be used to protect the compressor during cooling from high temperatures. This system can self-regulate the cooling system of the compressor.

► Cooling method: air cooling.

► Refrigerant: Use environmentally friendly refrigerants R404A and R23 that are not prohibited by the Montreal Convention or the London Amendment and the new US Environmental Protection Agency law.

► Energy-saving adjustment mode: cold-end PID adjustment mode (that is, heating without cooling, cooling without heating), which saves about 30% of energy than the balanced temperature adjustment method. The cooling capacity can be adjusted intelligently, and it can be adjusted automatically according to the temperature state, so as to quickly realize the temperature change and temperature balance. Compared with ordinary heat and cold balance control, the temperature response speed is faster, the power consumption is lower, the temperature deviation and fluctuation in the box are smaller, and the temperature overshoot is effectively avoided

► Chamber bottom plate:

Three special movable bottom plates are used to connect the chamber:

One is the bottom plate with holes, which is used for vertical vibration;

One is a bottom plate with a square hole, which is used when it is used with a horizontal slip table;

A blind plate, used when not shaking.

There is a condensate drain groove on the bottom of the shaker to prevent the condensate from flowing into the shaker.

► The fit of chamber and shaker

With the head expander and with the slip table

Any special requirement please feel free to contact us, we will try our best to realize it.


Connection mode:


Vibration test systems and test chamber connect directly


Vibration test systems and test chamber connect through transition connector


Vibration test systems and test chamber connect through the table

Vibration horizontal direction connedted with chamber

Customer Services

Presales:

• Technical consultation: test method, laboratory planning and suggestion.
• Equipment selection: selection scheme, FAQ.
• Product testing scheme.

In-Sales:

• Customer communication and progress report.
• Guidance for pre-installation preparation, equipment commissioning and test run.
• Calibration (when Third Party’s verification is required).

After-Sales:

• Technical training: operation of equipment, daily maintenance, common fault diagnosis and troubleshooting.

• Scheduled on-site service: Detection of problem as soon as possible in order to eliminate equipment and anthropogenic hazards. This is to ensure long term and stable equipment operation as well as delivery of latest technical information.

• Technical support: special paid services are provided according to customer’s needs.

Company Profile:

Labtone Test Equipment Co., Ltd. is a +15 year China manufacture of reliable, cost-effective equipments. Our superior products mainly include: Vibration Test Systems, Shock Test Systems, Bump Test Systems, Drop Tester, Packaging Transportation Simulators, and Combined Environmental Test Chambers.

Labtone started business in 2002 in a plant located in Shenzhen and moved to our new, expanded 6,000 square meter facility in Dongguan, Guangdong in 2015. Today, our products are found around the world in electronics, automotive, aerospace, telecommunication, optoelectronics instrument and industrial machinery applications. Our experience and commitment to new product development has resulted in products that are easy to use, accurate and designed for decades of service.

Labtone products carry a one-year(12months) warranty. We provide comprehensive factory services and supports, technical literatures, manuals and guides as well as having qualified staffs and experts to solve your problems.

We sincerely invite you to visit our factory.